Category Archives: Stages – X and Z axis

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

 

motion control - electric cylindermotion control - moticont

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Motion Control – Linear Voice Coil Motor Tolerates Tilting

Motion Control – Linear Voice Coil Motor Tolerates Tilting

motion control - voice coil motors


motion control - moticontVan Nuys, CA — Motion Control – Moticont has added a new 1.25 in (31.8 mm) stroke linear DC motor to its series of LVCM Linear Voice Coil Motors. The new LVCM-051-051-06 Linear Voice Coil Motor has been designed with a larger radial air gap to tolerate the tilting and misalignment that can be experienced when clamping out of parallel objects or moving off-center loads. This compact linear motor is 2.000 in (50.8 mm) in dia. with a 2.00 in. (50.8 mm) long housing and at mid stroke is just 2.88 in. (73.0 mm). 
Peak force is 9.5 lb (42.2N) at a 10% duty cycle and continuous force is 3.0 lb (13.3 N). Features of this low inertia, high acceleration / deceleration, clean, efficient, zero cogging, brushless voice coil servo motor makes it ideal for: Sorting, packaging, sampling, work holding and clamping, laser machining and drilling, wafer handling, and medical and pharmaceutical applications.

Motion Control – Low Cost, High Precision Vertical Lift Stage from OES!

Motion Control – Vertical Lift Stage

motion control - vertical stage

motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – The AT10-120 Motorized Vertical Stage from Optimal Engineering Systems, Inc. (OES) is a high resolution, low profile, high load vertical lift stage that can be easily integrated into almost any application. The large 220 mm x 140 mm (8.7 in. 5.5 in.) drilled and tapped platform has a vertical travel of 110 mm (4.3 In.).

Motion Control – Large Open Aperture XY Alignment Stages Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Alignment Stage

motion control - alignment stage


motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – New high resolution and high repeatability Alignment Stages have been released by Optimal Engineering Systems, Inc. (OES). Supplied with a standard 4 mm-per-turn ground lead screw, the AU200-200×200 Alignment Stages feature 200 mm (7.874 in.) of travel in both the X and Y axes. These low profile 80 mm (3.179 in.) high XY stages have a 250 mm x 250 mm (9.842 in. x 9.842 in.) open aperture.

Motion Control – Compact Direct Drive Linear Actuator Has Integrated Encoder and Temperature Sensor for Increased Throughput!

Motion Control –  Linear Actuator features Increased Throughput!
motion control - linear actuators


motion control - moticont

 

Van Nuys, CA – Motion Control – The Compact SDLM-051-070-01-01 Direct Drive Linear Actuator with integrated position and temperature sensors is the latest addition to the patented series of zero backlash, zero cogging, high acceleration, high speed, high resolution, long life actuators from Moticont. This direct drive linear Actuator, also referred to as an Electric Cylinder is 2.000 in. (50.9 mm) in diameter and the compact housing length is just 2.750 in (69.9 mm).

Motion Control – High Precision, XAB Triple-Axis (2 Goniometers and X-Axis) Stage Available from OES!

Motion Control –  Triple-Axis Stage!

motion control - tri-axis stages


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of compound angles or the rotation of an object to precise angular positions.

The XAB-050-XX-01 integrates a two-axis Alpha-Beta goniometer on top of a single-axis linear actuator. The Beta-axis has a travel range of +/- 15 degrees with a rotation height of 50 +/- 0.2 mm.

Motion Control – Low Inertia, High Precision, Hollow Core Voice Coil Motor from Moticont!

Motion Control – Hollow Core Voice Coil Motor


Van Nuys, CA – Motion Control Components – A low inertia hollow core voice coil or moving coil linear motor from Moticont, the HVCM-051-025-019-01, features high acceleration, precise positioning to less than one micron (0.00004 in.), high reliability, and low cost. This cleanroom friendly, non-commutated motor is available off-the-shelf. The HVCM-051-025-019-01 hollow core voice coil linear motor has an open apertures of 0.750 in. (19.05 mm).
motion control - moticont

The hollow core allows for optics, illumination, laser beams, or cables to pass through.

Motion Control – Low Cost, Long Range of Travel, High Precision, Low Profile, Motorized, Profile Rail Linear Guide Stages Are Available from OES

Motion Control – Profile Rail Stages

motion control - linear stages


motion control -oesVan Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) has added five new profile single axis positioning stages to their AQ150 Series of linear stages. Available off-the-shelf in travel lengths of: 600 mm (23.622 in.), 700 mm (27.559 in.), 800 mm (31.496 in.), 900 mm (35.433 in.), and 1000 mm ( 39.370 in.), these stages are available with either a Two-Phase Stepper Motor or with a Three-Phase Brushless Motor with a Quadrature Incremental Optical Encoder.

Motion Control – Open Aperture XY Stages from OES Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Stages!

motion control- xy stages

Van Nuys, CA – — Motion Control – Two new high resolution, high repeatability XY stages have been released by Optimal Engineering Systems, Inc. (OES). The AU200-15×15-01 Motorized Stage (pictured) and the AU200-15×15-04 Motorized Stage are powered by Two-Phase Stepper Motors and have high 0.25 micron resolution and high 1.5 micron repeatability.

motion control - OES

The AU200-15×15-04 stage includes Quadrature encoders for position verification. Both stages have a large 3.54 in. x 3.54 in. (90 mm x 90 mm) platform with large open aperture and feature standard 1 mm-per-turn ground lead screws, and precision V-grove and Cross Roller guides.

Motion Control – Low Cost 1, 2, 3, and 4 ADAGIO Axis Stepper Motor Motion Control Systems Available from Optimal Engineering Systems, Inc. (OES)!

Motion Control – Stepper Motor Motion Control Systems

motion control - stepper motor controller


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – To complement the Optimal Engineering Systems’ (OES) expanding line of single and multi-axis motion control stages, OES has added the ADAGIO-X-STPR Series of Motion Control Systems.

Motion Control – NEW! Three-axis Gimbal Mount with Three-Phase Brushless Servo Motors has Higher Resolution and Speed!

Motion Control – Servo Motor Three-axis Gimbal Mount!

motion control - gimbal mount

Van Nuys, CA – The New AU300-AER-02 Three-axis Gimbal Mount from OES (Optimal Engineering Systems, Inc.) with Three-Phase Brushless Servo Motors and Quadrature Incremental Encoders features very high resolution and high speed. Each axis features: Low backlash worm gear drives and precision “V” groove and cross roller bearings for high accuracy and repeatability. The typical accuracy is 0.05° equal to 180 arcsec and typical repeatability is +/- 0.01° equal to +/- 36 arcsec. The maximum travel speed of each axis is 45° per second.

motion control -oes

This new three-axis gimbal mount handles loads up to 10 kg (22 lbs) and has a clearance of 300 mm x 300 mm (11.8 in. x 11.8 in.) around the roll axis stage and each stage is capable of the full 360° rotation of its axis. The azimuth axis rotary table is mounted on a large 360 mm (14.173 in.) x 360 mm (14.173 in.) x 13 mm (0.512 in.) plate with handles and has predrilled accessible mounting holes for easy integration into new or existing applications and for increased stability.

Motion Control – Select from the Large Variety of Precision XYZ Axis Stages to Suit Your Specific Application from Optimal Engineering Systems, Inc. (OES)!

Motion Control –  XYZ Axis Stages to Suit  Specific Applications!

motion control - custom stages
motion control - stages - custom

 

 

Van Nuys, CA – — Motion Control – OES (Optimal Engineering Systems) has introduced a series of high precision, low cost XYZ positioning stages that can be easily integrated into new and existing applications. They are offered in 5 travel lengths for each axis, 50 mm (1.969 in.), 100 mm (3.937 in.), 150 mm (5.906 in.), 200 mm (7.874 in.), and 300 mm (11.811 in.). Any combination of lengths, motors, and lead screws are available.

The two-phase stepper motors are standard with a knob for manual adjustment. The knob can be replaced with an incremental quadrature encoder for position verification.

Motion Control – XZ-Axis Motorized Linear Positioning Stages feature 1 Micron Repeatability from Optimal Engineering Systems, Inc. (OES)!

Motion Control – XZ-Axis  Positioning Stages

motion control - positioning stage

 


motion control - OESThe high precision 1 mm per turn lead screws and crossed roller bearings are used in these black anodized stages. They are deal for: Sampling, assembly, sorting, testing, laser drilling and machining, and positioning in lab and manufacturing environments.Van Nuys, CA – — Motion Control – OES (Optimal Engineering Systems) has added a new series of 15 mm, 30 mm, 50 mm, and 75 mm Linear Motion Positioning Stages to their broad selection of precision motion control components. Each of these motorized XZ-Axis Linear Positioning Stages features 1 micron repeatability and 10 micron positional accuracy. Both the X-axis (horizontal axis) and the Z-axis (vertical axis) have the travel lengths of 15 mm, 30 mm, 50 mm, and 75 mm and even longer to meet your application requirements.

The XZ-Axis linear stages are available with either stepper motors with knobs for manual adjustment which can be replaced with optical encoders for position verification. The stages are also available with servo motors and encoders for closed loop operation and higher operating speeds.

These XZ-Axis Motorized Linear Positioning Stages are compatible with the OES (Optimal Engineering Systems) line of motion controllers and are available as a complete plug-and-play system. Please consult the OES sales team for longer travel lengths or if custom mounting configurations are required.

About OES – Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders.

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information, contact sales team at: OES, 6901 Woodley Ave.; Van Nuys, CA 91406; Telephone: 888-777-1826 or +1 818-222-9200, FAX +1 818-436-0446 or E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com


See this and other Motion Control Components from OES (Optimal Engineering Systems, Inc.) featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

OES is on Facebook

OES is on Twitter

OES Videos