Category Archives: Controller – Brushed

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

 

motion control - electric cylindermotion control - moticont

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Motion Control – The first e-road bikes and e-MTBs with the lightweight maxon BIKEDRIVE AIR have arrived!

Motion Control – e-road bikes and e-MTBs!

Italian premium road bike manufacturer, Cipollini and Swiss bike manufacturer, TRANSALPES launch their new lightweight e-bikes with the maxon BIKEDRIVE AIR

motion control - application


motion control - maxon motorsTaunton, MA — Motion Control Products – The Cipollini Flusso is a performance e-road bike that weighs only 10.7 kg. With a weight of less than 16 kg, the TRANSALPES E1 sets standards in the electrified trail and enduro segment. Both e-bikes put a natural feel at the center of the riding experience.

There is an emerging trend in the e-bike market towards lightweight systems that are almost indistinguishable from standard bicycles. This development is supported by smaller, more powerful motors and improved battery technologies. “Integration is the key word,” says Michele Tittonel, R&D Coordinator at Cipollini. “The second generation of e-race bikes will be powered by electric motors fully integrated into the bike design and complemented with high-end components.”

Cipollini set out to develop one of the lightest e-race bikes in the world without compromising reliability and duration of assistance. Now the Italian bike manufacturer is introducing the new Flusso, which weighs just 10.7 kg

The Cipollini Flusso is equipped with maxon’s BIKEDRIVE Air system, which weighs just 3.5 kilograms including the battery. At its heart is a mid-mounted motor that delivers 30 Nm of torque. Thanks to a special free-wheel technology it’s easy to pedal even without electric assistance. Michele Tittonel says, “The natural feeling of riding is absolutely crucial; after all, physical effort should remain part of the experience.”

motion control - maxon application

Integration of the drive is also a top priority for the Swiss bike manufacturer TRANSALPES. “With the BIKEDRIVE AIR system from maxon, we want to build perhaps the lightest e-bike for demanding mountain bikers,” as co-owner Michel Juhasz explains. “The new TRANSALPES E1 rides as naturally as a mountain bike without a motor.” TRANSALPES’ lightest e-bike, with a carbon frame, weighs less than 16 kg.

The Cipollini e-road bikes and TRANSALPES e-MTBs can be configured and pre-ordered on the manufacturers’ websites.

For additional information, please visit: www.maxonbikedrive.com or contact us at info.us@maxongroup.com or 508-677-0520.

Also see Maxon-Light-Invisible-E-bike-System.shtml

About Maxon

The Swiss specialist for quality drives maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications, for example. To maintain its leadership in this demanding market, the company invests a considerable share of its annual revenue in research and development. Worldwide, maxon has more than 3000 employees at nine production sites and is represented by sales companies in more than 30 countries.

Maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. With over 50 years of experience in drive technology, maxon works closely with engineers designing high-tech innovations. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications. Worldwide, maxon has more than 2800 employees at nine production sites and is represented by sales companies in more than 30 countries. www.maxongroup.com

Contact maxon for more details https://support.maxongroup.com/hc/en-us/requests/new

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon’s trade show experience goes virtual
motion control tradeshow

This year, the COVID-19 pandemic has led to the cancellation of nearly all trade shows. Despite this, maxon is offering a digital trade show experience to all of its customers and anyone who’s interested in learning about the latest in drive technology. Visitors to maxon’s virtual booth will discover the benefits of our latest products such as the MiniMACS6 master controller, learn about high torque brushless DC motors as well as flat motors for robotics, and get to know the Mars rover. Visit virtualbooth.maxongroup.com and contact us to get your ideas moving.

If you prefer watching an entertaining video introducing all the latest products maxon brought to the market this year, you will find it here: https://youtu.be/Jtw7Hwxbdr4 a> Have fun watching! For more information please contact us at info.us@maxongroup.com or 508-677-0520.

For Information on Maxon’s Virtual Trade Show CLICK HERE

motion control - miniature components


See this and other Motion Control Components from Maxon featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

View 2021/2022 Maxon Catalog

 

motion control - maxon motors

 

Motion Control – From soaring heights: Camera stabilization with maxon drives!

Motion Control – Camera stabilization System!

Aerial images can be beneficial for many businesses and industries. Often things are revealed from above that are hidden to the observer on the ground. Drives from maxon are used in camera stabilizer systems.

motion control - Application


motion control - maxon motors

 

Taunton, MA — Motion Control Application – Mining companies, for example, survey mines from the air, oil and gas suppliers monitor their drilling rigs, and energy utilities monitor their overland lines. All these applications have one big challenge in common: In these often rough operating environments, the camera needs to be protected against wind, turbulence and the vibration of the carrier aircraft while being kept in a stable position. This is the job of a high-precision stabilization camera gimbal. These gimbals provide users with a stable and level platform that allows them to capture high-quality aerial images.

Motion Control – Maxon Motors Are in A New Docking System for Space Rendezvous!

Motion Control – Docking System for ISS!

The European Space Agency (ESA) is working on a new system to enable easy docking between two spacecraft. maxon developed two special drive systems for this purpose.

motion control - ISS docking system

motion control - maxon motor

 

Taunton, MA — Motion Control Products – Even though it’s been done many times before, the docking maneuver between two objects in space is always a delicate and potentially dangerous procedure. The speed is extremely high (about 28,000 km/h in case of the ISS), and corrections are difficult. For example, when the two objects are about to meet, maneuvering thrusters can no longer be used, since their exhaust plumes can cause damage. To prevent harm, cargo transporters are caught by a robotic arm installed in the International Space Station (ISS) and berthed manually. Manned spacecraft on the other hand dock directly in a computer-controlled process.

Motion Control – Maxon Expands its range of configurable drives!

Motion Control – Miniature Configurable Drives!

Maxon is once again expanding its range of configurable drives with more brushless DC motors, gearheads, and encoders from the ECX series.


motion control - maxon

 

 

Taunton, MA — Motion Control Products – The ECX series is growing with the addition of the maxon ECX Speed 4. This tiny powerhouse with a diameter of only 4 millimeters is designed for use in medical technology. The brushless DC motors are available in 2 versions: M (medium) and L (long) and can reach speeds of up to 50,000 rpm. They can be combined with the new GPX 4 C gearheads, which are available as two, three, or four-stage versions. With the GPX planetary gearheads, the pressure angle of the toothing has been optimized to achieve longer uptimes.

Motion Control – Maxon’s UAV propulsion system is Safe, Efficient and Ready for Take-off!

Motion Control – UAV Propulsion System!

Maxon BLDC motors were specifically designed for extreme durability and maximum reliability in professional UAVs.

motion control - - uav propulsion system


motion control - maxon motors

 

 

Taunton, MA — Motion Control Products – maxon actively supports UAV manufacturers with their ambitious designs, up to certification. Our UAV product portfolio offers matched combinations of motors, ESCs and propellers, for optimized propulsion systems providing maximum efficiency and reliability. Hence, operational safety and flight time are maximized, and costs of ownership dramatically cut down

motion control - EC69 specifications

Motion Control – High Precision, XAB Triple-Axis (2 Goniometers and X-Axis) Stage Available from OES!

Motion Control –  Triple-Axis Stage!

motion control - tri-axis stages


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of compound angles or the rotation of an object to precise angular positions.

The XAB-050-XX-01 integrates a two-axis Alpha-Beta goniometer on top of a single-axis linear actuator. The Beta-axis has a travel range of +/- 15 degrees with a rotation height of 50 +/- 0.2 mm.

Motion Control – New Galil DMC-21×5 Multi Axis Motion Controller is Available from Electromate!

Motion Control – Multi Axis Motion Controller

motion control - multi-axis controller

Vaughan, Ontario, Canada — Motion Control Components — The DMC-21×5 is the latest addition to the Econo family and is an easy upgrade path from the long running DMC-21×3 series. The DMC-21×5 utilizes nearly all of the same peripherals as the DMC-21×3 controller, making the transition simple.

motion control - electromate- robotics

The main difference between the DMC-21×5 and its predecessor is a state of the art ARM based processor that places its communication, command processing and memory capabilities on par with Galil’s line of current generation motion controllers, while still remaining at the Econo Series price of the DMC-21×3.

Motion Control – Low Cost, Long Range of Travel, High Precision, Low Profile, Motorized, Profile Rail Linear Guide Stages Are Available from OES

Motion Control – Profile Rail Stages

motion control - linear stages


motion control -oesVan Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) has added five new profile single axis positioning stages to their AQ150 Series of linear stages. Available off-the-shelf in travel lengths of: 600 mm (23.622 in.), 700 mm (27.559 in.), 800 mm (31.496 in.), 900 mm (35.433 in.), and 1000 mm ( 39.370 in.), these stages are available with either a Two-Phase Stepper Motor or with a Three-Phase Brushless Motor with a Quadrature Incremental Optical Encoder.

Servo Controller for Non-comutated Devices, e.g. voice coil motors, from Equipment Solutions!

Motion Control – Servo Controller for Non-comutated Devices!

motion control - Voice Coil Motor Controller

SCA601 Linear Servo Controller: High Performance analog PID Servo Control law; Digital control of PID tuning parameters; Analog Position Sensor input; High current linear amplifier; RS232 interface; 76 x 76 x 25


motion control - miniature components

 

 

Forestville, CA, – — The SCA601 Linear Servo Controller was specifically designed to control single phase, non-comutated devices like voice coil motors. It is a high performance single axis DC motor controller and amplifier system. It is comprised of a highly integrated single PC board level product with a cohesive interface and a compact heat sink.

Motion Control – Maxon is expanding their positioning controllers in the micro segment!

Motion Control –  Micro Positioning Controllers!
Maxon has introduced the EPOS4 Compact 24/5 EtherCAT 3-axes Controller as they continue expanding teir range of miniature controllers.

motion control - miniature controller


motion control - maxon

 

Taunton, MA — Motion Control Products – The EtherCAT version of the EPOS 4 Micro 24/5 positioning controller is another brand-new product. The controller’s functionality, operation, software, and accessories are derived almost directly from the existing products in the EPOS4 range. It is suitable for use with both brushed DC and brushless EC motors with a continuous power of up to 120 W and has comprehensive feedback options such as Hall sensors, as well as digital incremental and SSI absolute encoders.

Motion Control – Maxon Gearheads – Great power in Compact Form!

Motion Control – Maxon Gearheads – Great power in Compact Form!

motion control - gearhead cutaway

Micro gearheads from maxon with improved efficiency.

Taunton, MA — Motion Control Products – Maxon has developed a unique upgrade in the form of a new product series for its standard micro gearhead: A wide range of performance improvements offer new opportunities.
motion control - maxon

 

The first ideas for the UP-gearhead were inspired by ESA’s Mars project ‘ExoMars’ and NASA’s ‘Mars 2020’ project, where there was a need to ensure the highest possible availability even in extreme environmental conditions.

This also directly affects further parameters of the drive system: Given the same input power, ie. using the same motor and the same motor control system, the gearhead can deliver 30% more torque.

Motion Control – POSITAL Kit Encoders certified for compliance with BiSS interface standards are available from Electromate!

Motion Control – Kit Encoders Meet BiSS interface standards

motion control - kit encoders


motion control - electromate logoHamilton, New Jersey, August 2021 – POSITAL has received certificates of compliance for its family of kit encoders that feature BiSS C interfaces. These encoders are designed to be installed in motors or drives, providing the control system with position feedback to over single- or multi-turn operating ranges. “We have been enthusiastic supporters of open source, non-proprietary communications standards like BiSS,” comments Jörg Paulus, head of POSITAL’s European operations and a board member of the BiSS Association. “We are confident that by supporting the BiSS initiative and offering customers products that have been certified to comply with BiSS protocol standards, we will encourage further use of this versatile and cost-effective interface technology.”

Motion Control – NEW! Three-axis Gimbal Mount with Three-Phase Brushless Servo Motors has Higher Resolution and Speed!

Motion Control – Servo Motor Three-axis Gimbal Mount!

motion control - gimbal mount

Van Nuys, CA – The New AU300-AER-02 Three-axis Gimbal Mount from OES (Optimal Engineering Systems, Inc.) with Three-Phase Brushless Servo Motors and Quadrature Incremental Encoders features very high resolution and high speed. Each axis features: Low backlash worm gear drives and precision “V” groove and cross roller bearings for high accuracy and repeatability. The typical accuracy is 0.05° equal to 180 arcsec and typical repeatability is +/- 0.01° equal to +/- 36 arcsec. The maximum travel speed of each axis is 45° per second.

motion control -oes

This new three-axis gimbal mount handles loads up to 10 kg (22 lbs) and has a clearance of 300 mm x 300 mm (11.8 in. x 11.8 in.) around the roll axis stage and each stage is capable of the full 360° rotation of its axis. The azimuth axis rotary table is mounted on a large 360 mm (14.173 in.) x 360 mm (14.173 in.) x 13 mm (0.512 in.) plate with handles and has predrilled accessible mounting holes for easy integration into new or existing applications and for increased stability.

Motion Control – Maxon introduces a multi-axis controller for highly dynamic positioning tasks!

Motion Control – Miniature Multi-axis Controller

Maxon is launching the next generation of Motion Controllers with its MiniMACS6-AMP-4/50/10. The controller is ideal for use in applications where PLC solutions may be too expensive or cannot meet customer-specific requirements.

motion control - miniature controller

Taunton, MA — Motion Control Products – Maxon’s new multi-axis controller, the MiniMACS6-AMP-4/50/10, offers precise and highly dynamic control of up to six brushed DC motors or four brushless DC motors (up to 540 W continuous output power and 1.6 kW peak output power).

motion control - maxon motors

 

 

The controller is an economical and compact solution for system designers who develop autonomous robots or shuttle systems

A significant advantage of the new multi-axis solution is that it is programmable with the comprehensive ApossIDE automation software and the license-free Motion Control Library (written in C). Integrated bus interfaces enable efficient data exchange with higher-level controllers; however, it is also possible to run complete process sequences autonomously, without a PLC or PC. The MiniMACS6-AMP-4/50/10 will be available in early 2021.

Motion Control – Excellence Canada announces Electromate is a recipient of the 2021 Canadian Business Excellence Awards for Private Businesses!

motion control - electromate


motion control - electromateTORONTO, Canada — Motion Control – TORONTO, May 21, 2021 (GLOBE NEWSWIRE) – Electromate Inc. is pleased to announce that, at the upcoming fifth annual Canadian Business Excellence Awards for Private Businesses being held on Wednesday June 9th, Excellence Canada will be awarding Electromate with their Canadian Business Excellence Award.

“Recipients of this distinguished award have clearly demonstrated a strategic approach to successfully improving business performance and achieving goals, with a focus on the following three key performance areas: Delighted Customers; Engaged Employees; and Innovation,” says Allan Ebedes, President and CEO, Excellence Canada.

Excellence Canada’s mission is to help improve organizational performance and recognize excellence, with a vision to promote and enable excellence in every organization in Canada.

Motion Control – maxon celebrates International Women in Engineering Day!

Motion Control – maxon celebrates International Women in Engineering Day!

The women in engineering (WIE) at maxon work eagerly to contribute to the success of advanced technology in the motion control industry. This week in honor of International Women in Engineering Day, June 23, 2021 – maxon wishes to thank these engineering women for their contributions as they continue to help shape the world we live in.

motion control - engineers


motion control - maxon motorsTaunton, MA — Around the globe, the maxon women in engineering are working on motion control applications with their customers, they focus on new product designs to implement the latest technologies and continue to research new concepts and ideas for drive systems to be used in motion control applications found in Medical, Industrial Automation, Aerospace and Defense, and Mobility industries.

Motion Control – Electromate Recognized with 2021 AHTD Foundation Award!

Motion Control – Electromate 2021 AHTD Foundation Award!

motion control - electromate components


motion control - electromateToronto, Ontario – June 18, 2021 – Electromate received a Foundation Award from the Association for High Technology Distribution (AHTD), recognizing the company’s 25 years of membership and support. This is the first year the Award has been given, honoring a small group of members out of approximately 300 automation solution providers and manufacturers.

The AHTD is dedicated to maximizing the productivity, growth, and enterprise opportunities of its high-tech automation solution provider and manufacturer members. These goals align with Electromate’s commitment to driving innovation, identifying emerging technologies and products, promoting the education of automation and motion control, and fostering its relationships with industry peers.

Motion Control – ADVANCED Motion Controls releases Micro-sized high-power Servo Drive available from Electromate!

Motion Control – Micro-sized high-power Servo Drive!

Motion Control -miniature servo drive

Vaughan, Ontario, Canada – Motion Control – The FM060-25-CM is part of a new breed of micro-sized, high-power servo drives, immediately available from ADVANCED Motion Controls. Rated to output 25A continuous and 50A peak, this fully featured digital servo drive is small enough to fit in the tightest locations. It is ideally suited for mobile and portable applications such as mobile robotics, automated mobile robots (AMRs), AGVs, material handling, warehouse automation, lab automation and more.
motion control - electromate

 

 

The mounting footprint of the FM060-25-CM is 50.8mm x 25.4mm with a height of 22.1mm making it possible for up to 3 units to fit within the footprint of a standard business card. The FM060-25-CM uses CANopen for network communication. Along with this model are two lower current options, the FM060-10-CM rated to 10A continuous and FM060-5-EM rated to 5A continuous, designed to the same dimensions.

Drive specialist maxon, renowned for its Mars motors, is joining forces with the robotics startup ANYbotics!

Motion Control – Maxon and ANYbotics form New Partnership!

Motion Control Drive specialist maxon, renowned for its Mars motors, is joining forces with the robotics startup ANYbotics and will in future supply the drive systems of the autonomous ANYmal inspection robot. The robot will soon be marketed in large quantities. This cooperation will also benefit maxon, since ANYbotics provides important robotics know-how and is currently the most successful young company in this field.

motion control - maxon to supply drive systems

motion control - maxonTaunton, MA — Motion Control -A solid partnership: maxon and ANYbotics are entering into a close, long-term collaboration and are thus strengthening Switzerland as a prime location for robotics. One of the decisions made by the two partners is that maxon, as global drive specialist, will handle the future development and production of the actuators for ANYmal.